News Center

Company News

Industry News

Media News

Product Information

FAQ

How to Set One Row and Three Column Barcode for Zebra Printer

How to Set One Row and Three Column Barcode for Zebra Printer

How to set up a row and three columns of bar codes for zebra printers requires installing common software Bartender bar code printers, which can be set up in bar code software. hongxing yongli xiaobian explains the specific operation methods as follows: 1. open the Bartender, create a new "blank label format", and then directly click to complete 2. set up the page: file-> page setup. Select the paper, then the paper size can be selected "user-defined size (if there is no change option, you can first create a new paper size to be set)", the paper width and height enter the size of the label paper, as shown in the following figure: enter

10

2020

/

07

Zebra printer ribbon wrinkle ten reasons

Zebra printer ribbon wrinkle ten reasons

Ribbon/ribbon wrinkling is a common problem in bar code printers, most of which are caused by improper operation of staff. The following is an analysis and arrangement of the ten major causes of ribbon wrinkling in zebra printers by Hongxing Yongli: Provide reference! Barcode printer carbon tape reason 1: print head imbalance corresponding operation: turn off the power supply of the barcode machine, press and hold the "PASUE" key on the panel to turn on the power supply, and then release the finger until the machine automatically outputs paper. at this time, the machine enters the self-test mode and will print the test label. Observe the effect of the test page to judge the printer pressure. For example, the test page shows light on the left, black on the right, and large on the right,

10

2020

/

07

What is the reason why the data collector cannot be started normally?

What is the reason why the data collector cannot be started normally?

What is the reason why the data collector suddenly cannot be turned on and cannot be turned on normally? Hongxing Yongli's small compilation provides everyone's reference: if you encounter a handheld data collector that cannot be turned on, you can try the following methods to check the reason: youboxun handheld data terminal PDA 1) check whether the battery of the device is charged; 2) Check whether the battery of the equipment is installed correctly; 3) Check whether the power key of the equipment is in good contact; 4) Use the power adapter to charge for 10 minutes before trying to start the machine. 5).

10

2020

/

07

Handheld Terminal PDA Scanning FAQ

Handheld Terminal PDA Scanning FAQ

Hand-held terminal PDA scanning common problems, mainly light does not recognize the bar code, not light two common problems. The following Hongxing Yongli made detailed troubleshooting for it: 1) The light does not recognize the barcode, and the scanning card: A, the scanning head can be recalibrated; B, set to the corresponding scanning head mode; C, check the scanning program; D, restart the equipment; E, confirm whether the barcode is damaged; F, confirm whether it is in the correct scanning range and distance; G, confirm whether the barcode is the type of barcode that the device can recognize. 2) No light or abnormal light: A. Re-calibration

10

2020

/

07

Barcode printer is a professional barcode output device

Barcode printer is a professional barcode output device

Barcode printer is a professional barcode output device. In daily use, we should pay attention to those who use common sense. If we encounter some common minor problems, we can learn to exclude and check by ourselves. 1. The print head of bar code printer is the core of bar code machine, so it is necessary to regularly maintain the printer and insist on cleaning the print head in the process of application, so as to ensure the printing quality and prolong the service life of the print head. Use alcohol to clean the print head, rubber roller and ribbon sensor when printing a roll of labels. When changing the printing cable, turn off the power of the printer and computer first, and then connect the cable. (When cleaning the print head number, turn off the power first. The print head is a fine part,

10

2020

/

07

< 1...131415...36 >